Welcome to GOFASTMOTORSPORTS.com ... ... ... Green Flag - Green Flag - Go Go Go ... ... Brought to you by Ricks Satellite - Where the Big Dish Rules!

Ricks Satellite Wildfeed and Backhaul Forum
Register Latest Topics
 
 
 


Reply
  Author   Comment   Page 49 of 49     «   Prev   46   47   48   49
DarkSky

Registered:
Posts: 2,247
Reply with quote  #721 
Is this what you are looking for mac address. This is your dmesg log on post #700 of this thread.

Code:

[ 3245.873318] dvbdev: DVB: registering new adapter (Prof 7500 USB DVB-S2)
[ 3245.886520] usb 1-1: USB disconnect, device number 2
[ 3247.907199] dvb-usb: MAC address: 88:88:88:88:88:88
[ 3248.712995] stv090x_attach: Create New Internal Structure!
[ 3248.712998] stv090x_setup: Initializing STV0903
phkarmur

Registered:
Posts: 38
Reply with quote  #722 

Quote:
Is this what you are looking for for mac address. This is your dmesg log on post #700 of this thread.

Yes, but Its wrong MAC address
idk why but dvb loaded twice (logs from my post #700)
Code:

[ 3245.873318] dvbdev: DVB: registering new adapter (Prof 7500 USB DVB-S2)
[ 3245.886520] usb 1-1: USB disconnect, device number 2
[ 3247.907199] dvb-usb: MAC address: 88:88:88:88:88:88
[ 3248.712995] stv090x_attach: Create New Internal Structure!
[ 3248.712998] stv090x_setup: Initializing STV0903
[ 3248.758750] stv090x_setup: Setting up initial values
[ 3248.758913] stv090x_setup: Setting up Cut 2.0 initial values
[ 3248.758962] stv090x_attach: Attaching STV0903 demodulator(1) Cut=0xf8
[ 3248.758965] dw2102: Found STV0900 @0x6a
[ 3248.846715] stb6100_attach: Attaching STB6100 
[ 3248.846718] dw2102: Found STB6100 @0x60
[ 3248.846723] dw2102: Attached STV0900+STB6100A!
[ 3248.846730] usb 1-1: DVB: registering adapter 0 frontend 0 (STV090x Prof 7500)...
[ 3248.847113] rc rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/rc/rc0
[ 3248.878613] rc_core: IR keymap rc-tbs-nec not found
[ 3248.878619] Registered IR keymap rc-empty
[ 3248.878751] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/rc/rc0/input5
[ 3248.879040] dvb-usb: schedule remote query interval to 150 msecs.
[ 3248.879044] dvb-usb: Prof 7500 USB DVB-S2 successfully initialized and connected.
[ 3248.879205] usbcore: registered new interface driver dw2102
[ 3248.991305] stv090x_release: Actually removing
[ 3248.992183] dvb-usb: Prof 7500 USB DVB-S2 successfully deinitialized and disconnected.
[ 3249.943238] usb 1-1: new high-speed USB device number 3 using ehci-pci
[ 3250.316884] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2
[ 3250.321619] usb 1-1: New USB device found, idVendor=3034, idProduct=7500
[ 3250.321623] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3250.321625] usb 1-1: Product: DVB-S USB
[ 3250.321627] usb 1-1: Manufacturer: Prof Group
[ 3250.399906] dvb-usb: found a 'Prof 7500 USB DVB-S2' in cold state, will try to load a firmware
[ 3250.400067] dvb-usb: downloading firmware from file 'dvb-usb-p7500.fw'
[ 3250.400071] dw2102: start downloading DW210X firmware
[ 3250.615006] dvb-usb: found a 'Prof 7500 USB DVB-S2' in warm state.
[ 3250.615135] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 3250.616481] dvbdev: DVB: registering new adapter (Prof 7500 USB DVB-S2)
[ 3253.010734] dvb-usb: MAC address: 22:ab:10:3c:12:ff
[ 3253.011591] stv090x_attach: Create New Internal Structure!
[ 3253.011593] stv090x_setup: Initializing STV0903


Quote:
for mac address, maybe look in to dvbnet...

https://blogs.s-osg.org/the-role-of-dtv-network-interfaces-in-media-controller-support-for-dvb/

then use ifconfig to see the mac address of the dvbnet device..
 

this commands also give MAC address too, Its working for Prof dvb but idk for other devices
Code:

root@ubuntu:/home/parbat# dvbnet -p 100 -a 0 -n 0
DVB Network Interface Manager
Copyright (C) 2003, TV Files S.p.A
Status: device dvb0_0 for pid 100 created successfully.
root@ubuntu:/home/parbat# dvbnet -p 120 -a 0 -n 0
DVB Network Interface Manager
Copyright (C) 2003, TV Files S.p.A
Status: device dvb0_1 for pid 120 created successfully.
root@ubuntu:/home/parbat# sudo dvbnet -l
DVB Network Interface Manager
Copyright (C) 2003, TV Files S.p.A
Query DVB network interfaces:
-----------------------------
Found device 0: interface dvb0_0, listening on PID 100, encapsulation MPE
Found device 1: interface dvb0_1, listening on PID 120, encapsulation MPE
-----------------------------
Found 2 interface(s).
root@ubuntu:/home/parbat# ip addr|grep -A1 dvb
3: dvb0_0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 4096 qdisc pfifo_fast state UNKNOWN group default qlen 1000
    link/ether 22:ab:10:3c:12:ff brd ff:ff:ff:ff:ff:ff
--
4: dvb0_1: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 4096 qdisc pfifo_fast state UNKNOWN group default qlen 1000
    link/ether 22:ab:10:3c:12:ff brd ff:ff:ff:ff:ff:ff
root@ubuntu:/home/parbat# 

majortom

Avatar / Picture

Registered:
Posts: 4,937
Reply with quote  #723 
It's the same process regardless of dvb device.. though I generally never use that stuff.
I think as long as you see a net device under
ls /dev/dvb/adapter2
demux0  dvr0  frontend0  net0

below is from the dvbsky device that I have (actual mac address edited).
Code:
dvbdev: DVB: registering new adapter (DVBSky S960/S860)
[616544.405462] usb 1-3.2: media controller created
usb 1-3.2: dvb_usb_v2: MAC address: 00:11:22:33:44:55

sudo dvbnet -p 501 -a 2 -n 0

ifconfig
dvb2_0    Link encap:Ethernet  HWaddr 00:11:22:33:44:55

__________________
Perfect 10 7.5' mesh Chapparal C/Ku Co-Rotor feed, Norsat 8115 CBAND, Norsat 4106A Ku Thomson Saginaw Actuator, Vbox positioner,
Home Brew Polarotor683 Servo circuit. Openbox S9, Prof7500, v4l-updatelee linux drivers installed.
ricardo's geo-orbit archive: https://web.archive.org/web/20150516202529/http://www.geo-orbit.org:80/sizepgs/tuningp2.html#anchor469886
DarkSky

Registered:
Posts: 2,247
Reply with quote  #724 


I just finished pushing the last of the new kernel 4.12.0-rc2 to majortom's and my bitbucket so it will be in tune with UDL's latest kernel. It also has majortom's new 955Q IQ plot mod for the 955Q.

This kernel upgrade is for the PIXEL and Stretch images only.

Just follow the instructions in the README for compiling / installing. Pay attention and do the sections for the pi you are compiling for (pi 2/3 or pi 1).

Of course you can compile both kernels and install them on the same sdcard so you can switch between devices. If you are compiling for the pi 1 you can compile the kernel on the pi 2/3 so you can have the faster spped and use -j4 but still follow the pi 1 sections in the README.

https://bitbucket.org/dark-sky/rpi-udl-linux

VSB 8:

latest.png   

Ray

DarkSky

Registered:
Posts: 2,247
Reply with quote  #725 
I pushed majortom's latest 955Q IQ plot code improvements to our bitbucket and updated the picture in the last post to reflect the changes.

If you have already compiled the new kernel and have not done a distclean just do:

git pull
make -j4
sudo make -j4 modules_install
sudo reboot

Note:

The IQ plot for the 955Q is still a "Work in progress" so for now any attempt to use the drop down boxes in the IQ plot window for the 955Q plot will crash the IQ plot window. Do not use the drop down box until some more tweaks are done in updateDVB.
andyinyakima

Avatar / Picture

Registered:
Posts: 1,520
Reply with quote  #726 
Screenshot_2017-05-30_08-15-18.png

Just showing that UDL's USALS mods compiled and work on the RPi.


This compiled on my 4.11 Stretch version - the 4.9 Pixel version came up with a qwt failure.
Haven't done upgrade yet.





__________________
andyinyakima
-----------------------------------
Recs: TBS6983, TBS5925 __ Ant: 90cm on SG6100__OSes: Linux with v4l-updatelee drivers __ RPi2 with v4l-updatelee drivers

Open Book, Open Source, You have to Open it to Know what's in it!
DarkSky

Registered:
Posts: 2,247
Reply with quote  #727 
My latest project:

Majortom told me the other day that he had updated his router with the latest LEDE image. It appears that LEDE is a new fork of openwrt.

Majortom and I had bought some 3.0 usb 3 port usb adapters with a gigabyte Ethernet port (rtl8152 chip) a while back so I decided to use it as the second ethernet port and download the LEDE image for my pi2 and play with it. To my surprise my little pi2 works really well with my DSL as a router.

I tuned the SQM Qos for the best settings using dslreports.com speed test and I started a download of udl's kernel and with the traffic shaping in the router I do not think there was hardly any noticeable difference using the browser while cloning udl's kernel.

My results after tuning on dslreports.com:


speed-test.png 

Some pics of some graphs in the router's web page when I was downloading udl's kernel:

Attached Images
Click image for larger version - Name: 1.png, Views: 11, Size: 35.21 KB  Click image for larger version - Name: 2.png, Views: 11, Size: 77.28 KB  Click image for larger version - Name: 3.png, Views: 12, Size: 70.04 KB  Click image for larger version - Name: 5.png, Views: 12, Size: 66.14 KB  Click image for larger version - Name: 6.png, Views: 12, Size: 119.09 KB  Click image for larger version - Name: 7.png, Views: 11, Size: 108.58 KB  Click image for larger version - Name: new.png, Views: 11, Size: 93.70 KB 

Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.

Fellow Members, your posts are welcome here! Do not worry about posting everything perfect. Different receivers and LNB's will give you different Frequencies and Symbol Rates. Some set top boxes, PCI cards and USB receivers, Do Not Require all of the same information that others may need. It is not Required to post everything that others may need to tune in a feed. It is just most important to share the find. We can always adjust the Frequency and Symbol Rates and try the various Modulations and FEC's on our own receivers until we get a lock and then give a polite reply with what works for your receiver, as that information might help others as well. We all appreciate the efforts and energy of the Posters!

Thank You for Visiting GOFASTMOTORSPORTS.com - Keep Your Eyes on the Sky and the Track!